| Service Charges |
| Hourly Rate |
65.00 |
| Minimum Charge |
32.50 |
| General Gunsmithing |
| Long Guns |
| Clean &Oil (Complete Disassembly) |
60.00 |
| Revolvers |
| Python |
100.00 |
| Smith &Wesson |
75.00 |
| Semi-Auto |
75.00 |
| Trigger Adjustment |
Hr. Rate |
| Check Headspace |
45.00 |
| Chamber Cast |
70.00 |
| Bore Sight Rifle |
35.00 |
| Bore Sight &Sight Rifle In (Ammo Extra) |
75.00 |
| Remove Fired Stuck Case from Chamber |
Hr. Rate |
| Metal Finishing |
| Hot Blue Rebluing |
| Matte Finish (Bead Blast) |
125.00 |
| Deluxe Finish 400 Grit |
165.00 |
| Straw Wheel Finish |
200.00 |
| Gloss Finish 555 Polish |
210.00 |
| Barreled Action |
| Belgian Bluing |
225.00 |
| Stainless Steel Bluing |
| Matte Finish (Bead Blast) |
140.00 |
| Standard |
175.00 |
| NitreBlue Bluing (Small Parts) |
100.00 |
| Electroless Nickel Plating |
| Handguns Semi-Auto or Small Parts Only |
| Satin Finish |
175.00 |
| High Polish |
200.00 |
| Rifles/Shotguns |
| Satin Finish |
190.00 |
| High Polish |
215.00 |
| Stripping Electroless Nickel |
125.00 |
| Parkerizing |
125.00 |
| Spider Webbing |
45.00 |
| Per hole |
30.00 |
|
|
| Sight Work |
| Drill and Tap Barrel or Receiver for Sights |
| Per Hole |
30.00 |
| Cut Dovetail in Barrel |
75.00 |
| Install Front Sight Ramp |
| Sweat on Type |
60.00 |
| Screw on Type |
60.00 |
| Band Type |
Hr. Rate |
| Install Receiver Sight |
45.00 |
| Scope Mounting |
| Standard |
45.00 |
| Lapped & Bedded |
60.00 |
|
|
| Action, Barrel & Rifle Work |
| Cut and Crown Barrel |
70.00 |
| Chamber and Fit Barrel to Action |
| Model 70 Push Feed, Model 700, Model 77, Mauser 98, Savage |
200.00 |
| Model 70(Pre 64 and Classic), Ruger#1, Springfield Enfield |
250.00 |
| Install New Bolt Handle (Bolt Handle Extra) |
125.00 |
| Install Muzzle Brake (Brake Extra) |
125.00 |
| Muzzle Brake (11 Degree Slant Forward) |
65.00 |
| Barrel Fluting (6 Flutes) |
120.00 |
Accu-Job
Square Receiver
Recut Bolt Nose, Bolt Face, and Lugs
Open Bolt Shroud
Surface Grind Recoil Lug
Set Barrel Back Length of Neck
Recrown
Pillar Bed and Adjust Trigger |
395.00 |
|
|
| Shotgun Work |
| Polish Chamber/Bore |
50.00 |
| Install Screw in Choke (plus tube) |
125.00 |
|
|
| Handgun Work |
| Chamfer Revolver Barrel (Forcing Cone) |
40.00 |
| Chamfer Revolver Cylinder |
60.00 |
| Revolver Action Job |
85.00 |
| Rebarrel Revolver (Labor Only) |
| Factory Barrel |
50.00 |
| Custom Barrel |
200.00 |
| Straighten Crane on Revolver |
45.00 |
| Install Crane Lock |
45.00 |
| Remove/Modify revolver Hammer Spur |
40.00 |
| Convert Revolver From Square Butt To Round Butt |
100.00 |
| Semi-Auto Pistol Action Job (Parts Extra) |
100.00 |
| Tighten Slide on 1911 Auto |
80.00 |
| Fit Barrel on 1911 Auto |
140.00 |
| Fit And Install Barrel Bushing On 1911(Labor Only) |
80.00 |
| Bevel Magazine Well On 1911 Auto |
50.00 |
| Open and Modify Ejection Port on 1911 Slide |
Hr. Rate |
| Throat, Polish Barrel And Feed Ramp On 1911 Auto |
45.00 |
| Fit New Trigger on 1911 Auto (Labor Only) |
40.00 |
| Fit Custom Hammer on 1911 Auto (Labor Only) |
75.00 |
| Cut Slide For Bo-Mar(Labor Only) |
| Plain Cut |
125.00 |
| W/Side Shields |
155.00 |
| Cut Slide for Novak Rear (Labor Only) |
125.00 |
| Cut Slide for Dovetail Front Sight (Labor Only) |
75.00 |
|
|
| Stock Work |
| Wood Finishing |
| Basic Finish |
| Unfilled Oil or Lacquer finish on Average Stock |
125.00 |
| Deluxe Finish |
| Filled, Rubbed Oil Finish on Average Stock |
175.00 |
| Pillar Bedding Barreled Action |
| Hunting/Tactical Rifle |
125.00 |
| Bench Rifle |
190.00 |
| Install Recoil Pad (Pad Extra) |
60.00 |
| Install Adjustable Butt Plate (Butt Plate Extra) |
100.00 |
| Install Sling Swivels (Swivels Extra) |
45.00 |
| Install Recoil Reducer (Reducer Extra) |
80.00 |
| Stock Blank Inlet |
Hr. Rate |
